TECHNICAL ARTICLE

Powered by:

Ecofriendly Reduction of Methylene Blue with Polyurethane Catalyst

A number of physical, chemical, and biological technologies have been developed to address the issue of synthetic dyes in wastewater. One of the important chemical methods involves reduction of these stringent pollutants into less hazardous products. In this study, a cross-linked polyurethane foam (CPUF) was prepared from toluene diisocyanate (TDI), tetraethylenepentamine (TEPA), and polycaprolactone diol (PCL; Mw: 1000?g/mole). To avoid harmful reducing agents, ecofriendly reduction of methylene blue (MB) was executed with CPUF as catalyst where ascorbic acid and fresh juice extracts were applied as reducing agents. The FTIR and SEM analysis confirmed the chemical composition and porous morphology of CPUF, respectively. The 100% reduction of MB was recorded in just 15 minutes with ascorbic acid and CPUF, while similar result was obtained in 37 minutes in blank experiment composed of only MB and ascorbic acid. Thus, catalytic role of CPUF in reduction process was proved. Fresh fruit extracts also participated in the reduction process, but rate of reaction was accelerated in the presence of CPUF. The reusability study of the catalyst supported its stability and efficiency. All the successful reduction processes followed 1st-order kinetics with highest apparent rate constant for ascorbic acid. Furthermore, phytotoxicity evaluation proved safe reduction of MB with 60% germination index. Hence, it can be concluded that catalytic role of CPUF has been established with safe and biodegradable reducing agents which can be extended to other redox processes.

1. Introduction

Synthetic dyes are an indispensable contributor of modern civilization. They are involved all around from textile to pharmaceuticals. Above 105 different types of dyes are produced annually in a huge volume of > metric tons. A large amount of these dyes is added into wastewater during application and postapplication stages in industries which builds a serious concern. They are considered hazardous since they damage the physical and chemical characteristics of water and propagate harm to living organisms [1, 2]. Therefore, a very active area of research is dedicated to eradicate these dyes from wastewater. Various physical, chemical, and biological technologies are developed to address the issue of organic dye pollutants [3]. One of the chemical methods involves reduction of these stringent pollutants into less hazardous metabolites [4].

These reduction treatments are usually accompanied by some catalysts to speed up the process. Mostly, inorganic catalysts are used which poses issues of secondary pollution or regeneration after treatment. To overcome these obstacles, polymeric catalysts such as polyurethanes have been proposed [5].

Polyurethane is an exclusive class of synthetic polymers which contains urethane link (-NHCOO). It is well known for versatile applications from cushioning to coatings due to tunable properties [68]. Polyurethane foams are extensively involved in water treatment processes, directly and indirectly [9]. Mostly, such treatments are reported with adsorption mechanisms due to polarity containing active sites in the structure of polyurethane. However, catalytic role of polyurethane during reduction treatments has been investigated as well [5].

Previously, we studied reduction of methylene blue (MB) dye with linear and cross-linked polyurethane catalysts in the presence of sodium borohydride (NaBH4) as a reducing agent [5]. But, NaBH4 is a known hazardous substance which can penetrate through the skin and eye and inhalation. Therefore, in this study, the objective was to replace hazardous NaBH4 with some safe and ecofriendly reducing agents. To accomplish this objective, pure ascorbic acid and fresh juice extracts of Citrus limon (lemon) and Psidium guajava (guava) were applied as reducing agents. Ascorbic acid is a natural reducing agent well known for its antioxidant properties. It is also appreciated to protect the reducing power of other antioxidants such as tocopherol. In the human body, it is essential for anti-inflammatory actions, collagen synthesis, to prevent tissue damages and for basic cell organization. These functions are performed by ascorbic acid through redox circuits present in the cell [1012]. Furthermore, the motivation to select fruit juices was the presence of soluble ascorbic acid in fruit juices especially in citrus family [13, 14].

2. Materials and Methods2.1. Materials

Toluene diisocyanate (TDI) and tetraethylenepentamine (TEPA) were purchased from Sigma-Aldrich Co., USA. The polycaprolactone diol (PCL, Mw: 1000?g/mole) was obtained from Acros Organics, USA. Methylene blue (MB) and ascorbic acid were procured from Avonchem Ltd., UK, and Honeywell, USA, respectively.

2.2. Synthesis and Characterization of Cross-Linked Polyurethane Foam (CPUF)

The synthesis of CPUF was performed following the previous reported method [5]. The mole ratio of monomers was 2?:?1?:?1 for TDI, PCL, and TEPA, respectively. In a typical experiment, a weighed amount of PCL (5.5?g) was heated to melt at >40°C in an open glazed bowl. Then appropriate amount of TEPA (0.4?mL) was mixed in melted PCL with stirring of few seconds. In the next step, the calculated amounts of TDI (2.3?mL) and water (1?mL) were speckled promptly on the melted mixture of PCL and TEPA along with vigorous stirring. The whole blowing and gelling reaction was accomplished in 1-2 minutes. The cellular polyurethane sample was placed in an oven at 50°C for 4-8?h before further use.

The morphological characterization of synthesized polyurethane was performed by scanning electron microscope (SEM; QUANTA250, UK). The tracking of synthesis through chemical link development was monitored by Fourier transform infrared spectroscopy using ATR-FTIR spectrophotometer (Shimadzu IR Prestige-21, USA). The numbers of scans were 70 and resolution was 4.0. The spectra were recorded in transmission mode from 600?cm-1 to 4000?cm-1.

2.3. Reduction of Methylene Blue (MB) with CPUF and Ascorbic Acid

The catalytic activity of CPUF was verified by reduction of MB dye in aqueous solution where ascorbic acid was used as a reducing agent. A set of three test tubes was prepared in a typical experiment. One of these was charged with 2.5?mL of MB () solution, 2.5?mL of ascorbic acid () aqueous solution, and 0.25?g of CPUF. The second test tube was prepared as a blank I which contained only MB and ascorbic acid solutions of the same volume and concentration. The third one was considered as blank II and charged with only 2.5?mL of MB solution of the same concentration and 0.25?g of CPUF. Whole experimental setup was carried out at room temperature () in the laboratory. At regular time intervals, an aliquot was taken in quartz cell to record the progress of the catalytic process in terms of disappearance of blue color of MB by UV-Vis spectrophotometer (T90, PG Instruments Ltd). The reduction of MB (%) for all these experiments was calculated by using the formula as follows:where is the concentration of MB at zero time and is the remaining concentration of MB at any time of the process in terms of absorbance.

2.4. Reduction of Methylene Blue (MB) with Psidium guajava and Citrus limon Extracts

The natural extracts of fruits, i.e., Psidium guajava and Citrus limon, were also used as reducing agents in this study. Fruits were purchased from the local market. The Citrus limon was washed, cut at half, and squeezed, while Psidium guajava was grinded homogeneously with distilled water. Both of the extracts were filtered and centrifuged. The supernatants were used in further experiments. The experiments were conducted with 2.5?mL of MB () solution, 2.5?mL of fresh extract, and 0.25?g of CPUF along with a blank. This blank was composed of 2.5?mL of MB and 2.5?mL of fresh extract. In the next experiment, a mixture of ascorbic acid () solution and Psidium guajava or Citrus limon (50?:?50) was added with MB solution in the presence of CPUF. A parallel blank of the same composition was also monitored in the absence of CPUF.

2.5. Reusability of CPUF

The evaluation of reusability of CPUF was carried out up to five runs. In the first run, a specific amount of CPUF was used for the reduction process according to the procedure described above. The required time for completion of reduction process was examined with UV-Vis spectrophotometer. At the end of the first run, used CPUF was separated, washed, and dried in an oven at 50°C till constant weight before employing for the next run in a similar manner.

2.6. Phytotoxicity Study of Treated MB Solution

The phytotoxicity of treated and untreated MB solutions was evaluated through seed germination assay. The germination of the seeds of Triticum aestivum was observed according to the protocol set by Bibi et al. [15]. The seed germination was carried out on a filter paper in petri dishes containing appropriate volume of solution. This assay was conducted for 7 days at in darkness. The numbers of germinated seeds and root length were recorded at the end. All the procedure was performed in two replicates. Germination index (GI) was calculated by the following equation:

2.7. Kinetic Study of Reduction Process

The order of reaction and rate of reaction was determined by the kinetic study of reduction process at . All successfully catalyzed experiments with three proposed reducing agents, i.e., ascorbic acid, Psidium guajava, and Citrus limon, were selected. The standard kinetic models for zero order, 1st order, and 2nd order were applied. It was considered that is equivalent to (absorbance at zero time) and is equivalent to (absorbance at time ), where was determined by UV-Vis spectrophotometer at the max of MB, i.e., 665?nm.

3. Results and Discussion3.1. Characterization of Cross-Linked Polyurethane Foam (CPUF)

The FTIR spectra of monomers (TDI, PCL, and TEPA) and synthesized CPUF are shown in Figure 1. These spectra supported the development of urethane links in CPUF. The characteristic bands of TDI (-NCO at 2268?cm-1), PCL (-OH at 3496?cm-1and –C=O at 1729?cm-1), and TEPA (broad –NH band at 3275?cm-1) are clearly evident in respective spectra. However, all of these bands of monomers were replaced with characteristic band of urethane links such as –NH stretching vibration band at 3316?cm-1, –NH bending vibration band at 1537?cm-1, and –C=O stretching vibration band at 1723?cm-1 with a slight shoulder at 1700?cm-1. The shoulder of –C=O may appear due to the intermolecular H bonding in polymer structure. These transitions of IR bands strongly established the synthesis of polyurethane sample [6, 1618]. Other noticeable bands in IR spectra of synthesized CPUF were symmetric and antisymmetric bands of aliphatic –CH at 2933?cm-1 and 2855?cm-1, aromatic C=C stretching band at 1645?cm-1 and 1595?cm-1, and multiple stretching bands of ester C-O at 1064?cm-1, 1160?cm-1, and 1214?cm-1. These bands additionally confirmed the incorporation of TDI and PCL in structure of CPUF.

Figure 1: FTIR spectra of monomers (TDI, PCL, and TEPA) and cross-linked polyurethane foam (CPUF) as (a) synthesized CPUF and (b) used CPUF.

Furthermore, the FTIR spectrum of CPUF used in the reduction process of MB is also documented and presented in Figure 1. This spectrum was recorded to make a structural comparison between as such synthesized and used CPUF. Figure 1 has repudiated any chemical change in the structure of CPUF even after its application in reduction process. Hence, it can be concluded that CPUF has provided a reaction site and just acted as a catalyst in the observed reduction process [5].

Apparently, synthesized CPUF was cellular in nature. Its morphology was analyzed by SEM. Multiple images were recorded at different magnifications and two are presented in Figure 2. These images revealed the open porous structure of CPUF with an average size of 35.75??m. These pores facilitated the reduction process by bringing reactants closer to each other [5].

Figure 2: Images of CPUF captured by SEM.3.2. Reduction of Methylene Blue (MB) with CPUF and Ascorbic Acid

The reduction of MB was recorded with the UV-Vis spectrophotometer, and results are displayed in Figure 3. These spectra showed that there was a remarkable role of CPUF in the reduction process. The time required for complete reduction of MB in the presence of only ascorbic acid was 37 minutes (Figure 3(a), blank I), whereas complete reduction was observed in just 15 minutes in the presence of CPUF (Figure 3(c)). These results clearly exposed the catalytic role of cellular CPUF in the observed reduction process. The most plausible mechanism may involve the simultaneous adsorption of MB and ascorbic acid on the cellular structure of CPUF, thus providing the surface for their mutual interaction leading to redox reaction between them. In another supportive judgment, this redox reaction may be accelerated due to the presence of conjugated site, located next to the aromatic ring in the CPUF urethane link [1921].

Figure 3: UV-Vis absorption spectra recorded for the progress in reduction of MB dye: (a) 2.5?mL of MB () solution and 2.5?mL of ascorbic acid () solution named as blank I, (b) 2.5?mL of MB () solution with 0.25?g of CPUF named as blank II, (c) 2.5?mL of MB () solution and 2.5?mL of ascorbic acid () solution with 0.25?g of CPUF, and (d) comparison of percent reduction of MB as a function of time in (a), (b), and (c).

Furthermore, the UV-Vis spectra of blank II, composed of 2.5?mL of MB () solution with 0.25?g of CPUF, are also presented in Figure 3(b). It was observed that about 64.94% MB was removed from solution in 70 minutes. It may be accredited to the adsorption of MB on cellular CPUF as polyurethane has been extensively reported for adsorption processes [2228]. This adsorption of dye molecules may facilitate the redox process in the presence of ascorbic acid. Hence, CPUF acted as a catalyst in the reduction of MB as well as provided sufficient support matrix for the process.

3.3. Reduction of Methylene Blue (MB) with CPUF and Psidium guajava Extract

For safe and ecofriendly reduction study, Psidium guajava and Citrus limon were also applied to exploit their reducing activity. Both of these fruits are well known for ascorbic acid content in their extracts [13]. Therefore, fresh extracts were prepared and used in the reduction experiments. The progress of process was monitored and displayed in Figures 4 and 5. Figure 4(a) shows 98% reduction of MB with pure Psidium guajava extract in the presence of CPUF. The time for accomplishment of this process was almost 60 minutes. This long time indicated low efficiency of Psidium guajava extract in reduction process. To boost the reduction speed, ascorbic acid solution () was mixed with Psidium guajava extract in a 50?:?50 ratio. But this mixture was also less effective, only 71% reduction was observed in 60 minutes (Figure 4(b)). However, similar experiment with 0.25?g of CPUF showed appreciable results as shown in Figure 4(c). The reaction speed was accelerated to achieve 100% reduction in just 22 minutes. These results demonstrated the catalytic role of CPUF.

Figure 4: UV-Vis absorption spectra recorded for the progress in reduction of MB dye: (a) 2.5?mL of MB () solution and 2.5?mL of fresh Psidium guajava extract, (b) 2.5?mL of MB () solution and 2.5?mL of fresh Psidium guajava extract with 0.25?g of CPUF, and (c) 2.5?mL of MB () solution, Psidium guajava extract, and ascorbic acid (50?:?50) with 0.25?g of CPUF.Figure 5: UV-Vis absorption spectra recorded for the progress in reduction of MB dye: (a) 2.5?mL of MB () solution and 2.5?mL of fresh Citrus limon extract, (b) 2.5?mL of MB () solution and 2.5?mL of fresh Citrus limon extract with 0.25?g of CPUF, and (c) 2.5?mL of MB () solution, Citrus limon extract, and ascorbic acid (50?:?50) with 0.25?g of CPUF.3.4. Reduction of Methylene Blue (MB) with CPUF and Citrus limon Extract

Similar experiments were carried out with fresh Citrus limon extract, and results are given in Figure 5. Figure 5(a) shows 54% reduction in 60 minutes with pure Citrus limon extract. Thus, Citrus limon was less effective even than Psidium guajava in reduction process. A mixture of Citrus limon and ascorbic acid also showed low reduction, i.e., 58.68% in 60 minutes (Figure 5(b)), comparatively. Yet, 100% reduction of MB was recorded in 22 minutes with addition of CPUF as revealed in Figure 5(c). Hence, safe reduction process was possible with fruit extracts but rate was low. However, rate was accelerated with ascorbic acid and CPUF.

3.5. Reusability of CPUF

The stability of a catalyst can be evaluated in terms of reusability. The prepared catalyst, CPUF, was applied multiple times for reduction of MB, and time required for 100% reduction is documented and presented in Figure 6. The results showed very distinctive trend of catalyst reusability in contrast to the previous reports related to inorganic catalysts [29, 30]. This catalyst exhibited progressively enhanced efficiency in five runs of reduction of MB. It was observed that the completion time for reduction process was decreased in each succeeding run. This unique trend in efficiency may be appeared due to the exposure of more active sites on polymeric structure of catalyst with cleaning and detaching involved in each successive run [5].

Figure 6: Reusability of CPUF for 100% reduction of MB. R1 represents first run, R2 is for second run, and so on. Primary -axis shows reduction of MB (%) and secondary -axis shows time (min) required for 100% reduction of MB in each respective runs.3.6. Phytotoxicity of Treated MB Solution

The objective of the study was to use safe and ecofriendly reducing agents. The phytotoxicity results supported the achievement of the said goal. The 0% germination index or 100% germination inhibition was observed for T. aestivum seeds in pure MB solution (Figure 7(a)).

Figure 7: (a) Germination of seeds in the original MB solution. (b) Germination of seeds in the treated MB solution.

However, 60% germination index was calculated for dye solution treated with ascorbic acid in the presence of CPUF catalyst. An average shoot length and root length were 4.6?cm and 8.5?cm, respectively. Hence, the phytotoxicity experiment clearly showed that reduction of MB resulted in its transformation into the less toxic product [15].

3.7. Kinetic Study of Reduction Process

To determine the rate constant and order of reaction, kinetic analysis of reduction processes was carried out. The standard kinetic models for zero order, 1st order, and 2nd order were applied on successfully catalyzed reactions. The values of rate constant () and are presented in Table 1. These results revealed that all catalytic processes followed 1st-order kinetics as highest were obtained. The graphic presentation of results is displayed in Figure 8. The highest apparent rate constant was 0.1485?min-1 for reduction of MB with ascorbic acid and CPUF experiment. Hence, these results confirmed the ascorbic acid as most efficient reducing agent along with catalytic role of CPUF.

Table 1: Name of the kinetic models used, mathematical form of the kinetic models, regression coefficient (2), and rate constant () for reduction of MB with CPUF, ascorbic acid, and mixtures of ascorbic acid and Psidium guajava or Citrus limon extracts at temperature .Figure 8: Plot of ln() as a function of time (min) for reduction of MB; : reduction of MB in the presence of ascorbic acid and 0.25?g of CPUF, : reduction of MB in the presence of Citrus limon extract and ascorbic acid (50?:?50) and 0.25?g of CPUF, and : reduction of MB in the presence of Psidium guajava extract and ascorbic acid (50?:?50) and 0.25?g of CPUF.4. Conclusion

In this study, cross-linked polyurethane foam (CPUF) was prepared from TDI, TEPA, and PCL (1000?g/mole). The chemical composition of CPUF was confirmed by characteristic bands of urethane link (–NHCOO) present in FTIR spectra. The SEM images showed porous morphology which supported cellular appearance of the polymer. The catalytic activity of CPUF was evaluated by the reduction of MB solution. Safe and ecofriendly reducing agents such as ascorbic acid and fresh extracts of Psidium guajava and Citrus limon were used. All of these participated actively in reduction process with CPUF, but ascorbic acid was the most efficient reducing agent. Phytotoxicity analysis through seed germination assay supported ecofriendly reduction of MB with ascorbic acid. All the successful reduction processes obeyed the 1st-order kinetic model. Hence, catalytic role of CPUF has been established with safe and biodegradable reducing agents which can be extended to other redox processes.

Data Availability

The data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

This research work was supported by the Higher Education Commission of Pakistan under NRPU no. 20-4509/NRPU/R&D/HEC/14.

References
  1. H. Ali, “Biodegradation of synthetic dyes—a review,” Water, Air, & Soil Pollution, vol. 213, no. 1-4, pp. 251–273, 2010. View at Publisher · View at Google Scholar · View at Scopus
  2. F. Gönen and E. Köylü, “Environmental application of telon blue AGLF adsorption on sunflower pulp: a response surface methodology approach and kinetic study,” Journal of Chemistry, vol. 2016, Article ID 9621523, 10 pages, 2016. View at Publisher · View at Google Scholar · View at Scopus
  3. T. N. Ramesh and V. Pavagada Sreenivasa, “Removal of indigo carmine dye from aqueous solution using magnesium hydroxide as an adsorbent,” Journal of Materials, vol. 2015, Article ID 753057, 10 pages, 2015. View at Publisher · View at Google Scholar
  4. I. Bibi, N. Nazar, M. Iqbal et al., “Corrigendum to ‘green and eco-friendly synthesis of cobalt-oxide nanoparticle: characterization and photo-catalytic activity’ [Adv. Powder Technol. 28 (2017) 2035–2043],” Advanced Powder Technology, vol. 28, no. 10, p. 2796, 2017. View at Publisher · View at Google Scholar · View at Scopus
  5. M. Sultan, A. Javeed, M. Uroos et al., “Linear and crosslinked polyurethanes based catalysts for reduction of methylene blue,” Journal of Hazardous Materials, vol. 344, pp. 210–219, 2018. View at Publisher · View at Google Scholar · View at Scopus
  6. X. Huang, C. F. De Hoop, J. Xie, C.-Y. Hse, J. Qi, and T. Hu, “Characterization of biobased polyurethane foams employing lignin fractionated from microwave liquefied switchgrass,” International Journal of Polymer Science, vol. 2017, Article ID 4207367, 8 pages, 2017. View at Publisher · View at Google Scholar · View at Scopus
  7. P. Jain and T. Pradeep, “Potential of silver nanoparticle-coated polyurethane foam as an antibacterial water filter,” Biotechnology and Bioengineering, vol. 90, no. 1, pp. 59–63, 2005. View at Publisher · View at Google Scholar · View at Scopus
  8. D. K. Chattopadhyay and K. V. S. N. Raju, “Structural engineering of polyurethane coatings for high performance applications,” Progress in Polymer Science, vol. 32, no. 3, pp. 352–418, 2007. View at Publisher · View at Google Scholar · View at Scopus
  9. M. Sultan, “Polyurethane for removal of organic dyes from textile wastewater,” Environmental Chemistry Letters, vol. 15, no. 2, pp. 347–366, 2017. View at Publisher · View at Google Scholar · View at Scopus
  10. A. Umapathy, P. Donaldson, and J. Lim, “Antioxidant delivery pathways in the anterior eye,” BioMed Research International, vol. 2013, Article ID 207250, 10 pages, 2013. View at Publisher · View at Google Scholar · View at Scopus
  11. G. G. Martinovich, E. N. Golubeva, I. V. Martinovich, and S. N. Cherenkevich, “Redox regulation of calcium signaling in cancer cells by ascorbic acid involving the mitochondrial electron transport chain,” Journal of Biophysics, vol. 2012, Article ID 921653, 6 pages, 2012. View at Publisher · View at Google Scholar · View at Scopus
  12. C. Rekha, G. Poornima, M. Manasa et al., “Ascorbic acid, total phenol content and antioxidant activity of fresh juices of four ripe and unripe citrus fruits,” Chemical Science Transactions, vol. 1, no. 2, pp. 303–310, 2012. View at Publisher · View at Google Scholar
  13. Y. T. Szeto, B. Tomlinson, and I. F. F. Benzie, “Total antioxidant and ascorbic acid content of fresh fruits and vegetables: implications for dietary planning and food preservation,” British Journal of Nutrition, vol. 87, no. 01, pp. 55–59, 2002. View at Publisher · View at Google Scholar · View at Scopus
  14. A. M. Pisoschi, A. F. Danet, and S. Kalinowski, “Ascorbic acid determination in commercial fruit juice samples by cyclic voltammetry,” Journal of Analytical Methods in Chemistry, vol. 2008, Article ID 937651, 8 pages, 2008. View at Publisher · View at Google Scholar · View at Scopus
  15. I. Bibi, A. Sultan, S. Kamal et al., “Extraction and quantification of phenolic compounds from Prunus armeniaca seed and their role in biotransformation of xenobiotic compounds,” Korean Journal of Chemical Engineering, vol. 34, no. 2, pp. 392–399, 2017. View at Publisher · View at Google Scholar · View at Scopus
  16. T. V. Travinskaya, A. N. Brykova, Y. V. Savelyev, N. V. Babkina, and V. I. Shtompel, “(Bio)degradable ionomeric polyurethanes based on xanthan: synthesis, properties, and structure,” International Journal of Polymer Science, vol. 2017, Article ID 8632072, 10 pages, 2017. View at Publisher · View at Google Scholar · View at Scopus
  17. N. Özveren and M. Ö. Seydibeyo?lu, “The use of biodiesel residues for heat insulating biobased polyurethane foams,” International Journal of Polymer Science, vol. 2017, Article ID 6310198, 14 pages, 2017. View at Publisher · View at Google Scholar · View at Scopus
  18. M. Han, Q. Liu, B. Su, S. Sun, and C. Zhao, “Bioinspired polyethersulfone membrane design via blending with functional polyurethane,” International Journal of Polymer Science, vol. 2017, Article ID 2158124, 10 pages, 2017. View at Publisher · View at Google Scholar · View at Scopus
  19. H. W. Lu, S. H. Liu, X. L. Wang, X. F. Qian, J. Yin, and Z. K. Zhu, “Silver nanocrystals by hyperbranched polyurethane-assisted photochemical reduction of Ag+,” Materials Chemistry and Physics, vol. 81, no. 1, pp. 104–107, 2003. View at Publisher · View at Google Scholar · View at Scopus
  20. Z.-J. Jiang, C.-Y. Liu, and L.-W. Sun, “Catalytic properties of silver nanoparticles supported on silica spheres,” The Journal of Physical Chemistry B, vol. 109, no. 5, pp. 1730–1735, 2005. View at Publisher · View at Google Scholar · View at Scopus
  21. M. V. Lakshmikantham, Y. A. Jackson, R. J. Jones, G. J. O'Malley, K. Ravichandran, and M. P. Cava, “Tellurolate-induced deprotection of 2,2,2-trichloro-tert-butyloxycarbonyl (TCBOC) derivatives,” Tetrahedron Letters, vol. 27, no. 39, pp. 4687-4688, 1986. View at Publisher · View at Google Scholar · View at Scopus
  22. A. Mohammadi, M. M. Lakouraj, and M. Barikani, “Preparation and characterization of p-tert-butyl thiacalix[4]arene imbedded flexible polyurethane foam: an efficient novel cationic dye adsorbent,” Reactive and Functional Polymers, vol. 83, pp. 14–23, 2014. View at Publisher · View at Google Scholar · View at Scopus
  23. S. Shoabargh, A. Karimi, G. Dehghan, and A. Khataee, “A hybrid photocatalytic and enzymatic process using glucose oxidase immobilized on TiO2/polyurethane for removal of a dye,” Journal of Industrial and Engineering Chemistry, vol. 20, no. 5, pp. 3150–3156, 2014. View at Publisher · View at Google Scholar · View at Scopus
  24. E. E. Baldez, N. F. Robaina, and R. J. Cassella, “Employment of polyurethane foam for the adsorption of methylene blue in aqueous medium,” Journal of Hazardous Materials, vol. 159, no. 2-3, pp. 580–586, 2008. View at Publisher · View at Google Scholar · View at Scopus
  25. J. de Jesus da Silveira Neta, G. Costa Moreira, C. J. da Silva, C. Reis, and E. L. Reis, “Use of polyurethane foams for the removal of the direct red 80 and reactive blue 21 dyes in aqueous medium,” Desalination, vol. 281, pp. 55–60, 2011. View at Publisher · View at Google Scholar · View at Scopus
  26. M. M. Góes, M. Keller, V. Masiero Oliveira, L. D. G. Villalobos, J. C. G. Moraes, and G. M. Carvalho, “Polyurethane foams synthesized from cellulose-based wastes: kinetics studies of dye adsorption,” Industrial Crops and Products, vol. 85, pp. 149–158, 2016. View at Publisher · View at Google Scholar · View at Scopus
  27. L. Kong, F. Qiu, Z. Zhao et al., “Removal of brilliant green from aqueous solutions based on polyurethane foam adsorbent modified with coal,” Journal of Cleaner Production, vol. 137, pp. 51–59, 2016. View at Publisher · View at Google Scholar · View at Scopus
  28. M. Sultan, “Hydroxyapatite/polyurethane composites as promising biomaterials,” Chemical Papers, vol. 72, no. 10, pp. 2375–2395, 2018. View at Publisher · View at Google Scholar · View at Scopus
  29. W. Peng, F. Zhang, G. Zhang, B. Liu, and X. Fan, “Selective reduction of 4,4-dinitrostilbene-2,2-disulfonic acid catalyzed by supported nano-sized gold with sodium formate as hydrogen source,” Catalysis Communications, vol. 12, no. 6, pp. 568–572, 2011. View at Publisher · View at Google Scholar · View at Scopus
  30. M. Khaksar, M. Amini, D. M. Boghaei, K. H. Chae, and S. Gautam, “Mn-doped ZrO2 nanoparticles as an efficient catalyst for green oxidative degradation of methylene blue,” Catalysis Communications, vol. 72, pp. 1–5, 2015. View at Publisher · View at Google Scholar · View at Scopus

» Author: Misbah Sultan,1 Alina Waheed,1 Ismat Bibi,2 and Atif Islam3

» Reference: International Journal of Polymer ScienceVolume 2019, Article ID 3168618, 9 pageshttps://doi.org/10.1155/2019/3168618

» Publication Date: 07/02/2019

» More Information

« Go to Technological Watch





This project has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement n° [609149].

AIMPLAS - Instituto Tecnológico del Plástico | C/ Gustave Eiffel, 4 (València Parc Tecnològic) | 46980 - PATERNA (Valencia) - SPAIN                Powered by: SoftVT